Rx65-3-6A1 Instructions (v611)


PRODUCT: Rx65


Top connections

Bottom connections

Channels

Channels

1. DEFAULT SETUP

Item

Setting Details
Purpose:

Rx65-3 Conventional servo outputs for use with any transmitter

Red wire positive (+)
Black wire negative (-)

Battery 3-18v (if no BEC)
Observe polarities
H1 output

Motor
Ch3

Integrated forward/reverse ESC for brushed motors
Center off

F1 output 'A'
(P13)
On/Off
Ch5
Start disconnected, 0v (on) when channel is Low
Momentary action
F2 output 'B'
(P14)
On/Off
Ch6
Start disconnected, 0v (on) when channel is Low
Momentary action
F3 output 'C'
(P15)
On/Off
Ch7
Start disconnected, 0v (on) when channel is Low
Momentary action
F4 output 'D'
(P5)
Not relevant
Ch5
P5 controls 'D'
P5 set up for servo so F4 not used
P1
Servo
Ch1, Standard servo
P2
Servo
Ch2, Standard servo
P3
Servo
Ch3, Standard servo
P4
Servo
Ch4, Standard servo
P5
Servo
Ch5, Standard servo
P6
Servo
Ch6, Standard servo
P7
Servo
Ch7, Standard servo
L input

Auto-detect

Monitors single cell lipo when used with a voltage booster

Arming
Enabled Ch3 to center position (off)
Low Voltage Cutoff
Enabled Led 5-flash if triggered (LVC)
Failsafe Enabled Motor cuts on signal loss
Inactivity Sleep Disabled

2. EXAMPLE CONNECTIONS:


Motor (H1)

Motor (H1)

Led (F1 'A')

Led (P2)

Servo (P7)

Lipo booster (L)

'H' outputs are intended for brushed motors. This receiver has two H outputs but must be connected in parallel and used as one (H1). One is on the main receiver and the other is on the daughter board. Together it has a 6A rating. This is a maximum 'worst case' value usually measured by connecting a fully charged battery direct to a stalled motor.

'P' outputs are either 3.5v or 0v (ground). Leds need resistors to limit current to no more than 20mA. High brightness leds allow a lower current which is preferred (eg: 2-5mA). Google will reveal how to select resistor values but 220-470ohms will be safe starting values.

'F' outputs are buffered with a fet. They are 0v (ground) when on and floating (disconnected) when off. Up to 2A is possible but lower currents are much better. Current-limiting resistors are required for leds. The load is normally connected to positive and the F output provides a path to ground to switch it on. F outputs are marked with letters on the receiver (A, B, C and D). The are programmed as P outputs (P13, P14, P15 and P5). eg: F1 = A = P13.

The 'L' pad monitors a single cell lipo when used with a voltage booster. This allows the motor to be powered with a boosted voltage and benefit from the convenience of a single lipo. The receiver will cut power to the motor when the voltage falls to 3v (LVC). The L pad is not intended for use when powering a receiver direct from a single lipo.



3. BINDING

Bind once:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode.
3. Rx led should flash slowly; wait for it to go solid.
Change distance between Tx/Rx if binding does not work.




4. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; no signal or not bound if never stops).
5 flash = LVC/Brownout (voltage went too low; check battery/motor load).

5. PAPERCLIP CHANGES:
The following changes can be made by simply shorting two pads together (eg: with a paperclip):
1. Perform a 'Hard reset' (factory reset).
2. Change motor control between 'low off' and 'center off'.
3. Enable/disable LVC (eg: when using Nicads, NiHMs, LiFe cells).
4. Enable/disable Selecta.
5. Enable/disable Cruise Control/Failsafe.
'Paperclip' changes

6. PROGRAMMING:
This receiver has many other options that are described on the features page.
These are changed using a technique called 'programming': v611.


Home ¦ Videos ¦ About ¦ Buy ¦ Email