Rx65-2 Instructions (v611)


PRODUCT: Rx65


Connections

Channels

Channels

Tx21

1. DEFAULT SETUP

Item

Setting Details
Purpose:

Rx65-2 Train with any DT transmitter

Red wire positive (+)
Black wire negative (-)

Battery 3-18v
Observe polarities
H1 output

Motor
Ch1

Integrated forward/reverse ESC for brushed motors
Center off

F1 output 'A'
(P13)
Front Light
H1 (auto)
0v when on, disconnected when off; LED2 enabled
F2 output 'B'
(P14)
Rear Light
H1 (auto)
0v when on, disconnected when off
F3 output 'C'
(P15)
On/Off
Ch5
Start disconnected, 0v (on) when channel is Low
Momentary action
P1
Front Light
Auto action, 3.5v when on, 0v off
P2
Rear Light
Auto action, 3.5v when on, 0v off
P3
On/Off
Ch2, Idle high, 0v when channel is Low, Momentary action
P4
On/Off
Ch4, Idle high, 0v when channel is Low, Momentary action
P5
On/Off
Ch5, Start high, toggle when channel is Low, Latching action
P6
On/Off
Ch3, Idle low, 3.5v when channel is Low, Momentary action
P7
On/Off
Ch3, Idle low, 3.5v when channel is High, Momentary action
P8
Servo
Ch1, Standard servo
P9
On/Off
Ch3, Idle high, 0v when channel is High, Momentary action (from v611-11)
P10
On/Off
Ch3, Idle high, 0v when channel is Low, Momentary action (from v611-11)
P11
On/Off
Ch3, Start high, toggle when channel is High, Latching action (from v611-11)
P12
On/Off
Ch3, Start high, toggle when channel is Low, Latching action (from v611-11)
L input
Auto-detect

Monitors single cell lipo when used with a voltage booster

Arming
Enabled Ch1 to center position (off)
Low Voltage Cutoff
Enabled Led 5-flash if triggered (LVC)
Cruise control Enabled Outputs 'hold' last position on signal loss/Tx switched off
Inactivity Sleep Enabled Invoked after 1hour, Switch Rx off and on to restart
Battery Voltage flashes
Enabled
(from v611-15)
Press Bind button (Ch5) briefly and count flashes as described here
Flashes appear on LED2 output (F1)

2. EXAMPLE CONNECTIONS:


Motor (H1)

Led (F1 'A')

Led (P2)

Servo (P7)

Lipo booster (L)

'P' outputs are either 3.5v or 0v (ground). Leds need resistors to limit current to no more than 20mA. High brightness leds allow a lower current which is preferred (eg: 2-5mA). Google will reveal how to select resistor values but 220-470ohms will be safe starting values.

'F' outputs are buffered with a fet. They are 0v (ground) when on and floating (disconnected) when off. Up to 2A is possible but lower currents are much better. Current-limiting resistors are required for leds. The load is normally connected to positive and the F output provides a path to ground to switch it on. F outputs are marked with letters on the receiver (A, B, and C). The are programmed as P outputs (P13, P14 and P15). eg: F1 = A = P13.

The 'L' pad monitors a single cell lipo when used with a voltage booster. This allows the motor to be powered with a boosted voltage and benefit from the convenience of a single lipo. The receiver will cut power to the motor when the voltage falls to 3v (LVC). The L pad is not intended for use when powering a receiver direct from a single lipo.



3. BINDING

Bind once:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode.
3. Rx led should flash slowly; wait for it to go solid.
Change distance between Tx/Rx if binding does not work.




4. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; no signal or not bound if never stops).
5 flash = LVC/Brownout (voltage went too low; check battery/motor load).

5. PAPERCLIP CHANGES:
The following changes can be made by simply shorting two pads together (eg: with a paperclip):
1. Perform a 'Hard reset' (factory reset).
2. Change motor control between 'low off' and 'center off'.
3. Enable/disable LVC (eg: when using Nicads, NiHMs, LiFe cells).
4. Enable/disable Selecta.
5. Enable/disable Cruise Control/Failsafe.
'Paperclip' changes

6. PROGRAMMING:
This receiver has many other options that are described on the features page.
These are changed using a technique called 'programming': v611.


Home ¦ Videos ¦ About ¦ Buy ¦ Email