Rx65 Overview



Top

Bottom

Connectors

Blade Tx

Blade Tx

Dx3

Tx21

Tx22

PCB ID: 65a Not latest version
PRODUCT: Rx65
INSTRUCTIONS: Rx65-1 | Rx65-2 | Rx65-22 | Rx65-3 | Rx65-4 | Rx65-5 | Rx65-6
PROGRAMMING: v610

ALL FEATURES



DESCRIPTION:
Receiver for surface vehices.
All variants are physically identical and have the same software but different defaults.
All outputs can be changed individually by operator.

SPECIFICATION:
Variant

Rx65-1 Rx65-2
Rx65-22

Rx65-3 Rx65-4
Rx65-5

Rx65-6 Details
Purpose:

Train
with
joystick Tx

Train
with
Tx20
Tx21
Tx22

Conven-
tional
Car
with
joystick Tx
or
Dx3*

Boat
with
joystick Tx





* Rx65-5 for Dx3
'H' output:
(H-Bridge)
1
1
1
1
1
Integrated forward/reverse ESC for brushed motors
512 step PWM control

Motor control
'Low off' 'Center off' 'Center off' 'Center off' 'Center off'
Direction channel
Yes -
-
-
-
'P' outputs:
(Pads)
4
4
4
4
4
Signal pads for Servos and low current on/off switching
Special programs for car lights and other switching
1024 step Servos
Serial data feed

2A buffered output 1 1 1 1 1 All 4 P outputs can drive 20mA loads (eg: leds)
Output 'P1' controls Pad 'A' which can drive a 2A load

BEC:

Yes Yes Yes Yes Yes A 3.3v 500mA 'battery elminator circuit' output is available alongside P4


'L' pad:

Yes Yes Yes Yes Yes Lipo booster monitor
Low voltage protection for a single cell lipo when used with a voltage booster

'Selecta':

- Enabled
(Rx65-22)

- - - Selecta can activate and deactivate models without touching them
(Available on all variants but enabled on Rx65-22 only)

Size: 13.4 x 31.2mm (0.6x1.3")
'N' and 'W' versions are 5mm thick, 'C' and 'U' versions are 7.5mm
Weight: 1.7g ('N' version)
Pad spacing: 2.54mm (0.1")
Voltage range: 2.9-18v (20v 'absolute max', operates down to 2.6v)
Motor current 3A with 16kHz PWM (motor stalled at 100% throttle)
Rx current: 16mA
Rx outputs: 5 (see above)
Tx channels*: 14 max (9 tested)
Modulation: 2.4GHz compatible with 22ms DSM2 and DSMX Air
and 16.5ms DSM2 Surface
Range: Indoor/Outdoor

* = Channels that can be used to control receiver outputs (all outputs can be associated with any channel)

HARDWARE OPTIONS:
The 'N' version has no wires or connectors (bare board).
The 'W' option is 2 wires for power, 2 wires for the motor and heatshrink covering.
The 'Z' option is a 1.5mm pitch JST ZH socket (with correct pin polarities +-s).
The 'P' option is a 1.25mm pitch Molex PicoBlade socket (servo wires must be swopped).
The 'T' option is a 2.54mm (0.1") pitch Turned-Pin socket for P1, P2, P3 and the A output.
The 'U' option is a 150mm coax aerial with U.FL socket (the U.FL socket allows the arerial to be replaced).



INSTRUCTIONS:

Rx65-1 Rx65-2 Rx65-22 Rx65-3 Rx65-4 Rx65-5 Rx65-6 Change from previous version
Version v610
v610
v610
v610
v610
v610
v610
Toggle servo, Adjustable LVC, Prog3, Variant change (changes relative to v603)

PROGRAMMING:

Programming table Feature descriptions
Version v610
v610





Home ¦ Videos ¦ About ¦ Buy ¦ Email