Rx65-3 Instructions (v611)


PRODUCT: Rx65c


Connections

Channels

Channels

Tx21

1. DEFAULT SETUP

Item

Setting Details
Purpose:

Rx65-3 Train with any compatible joystick or DT transmitter

Red wire positive (+)
Black wire negative (-)

Battery 3-18v
Observe polarities
H1 output

Motor
Ch1

Integrated forward/reverse ESC for brushed motors
Center off

F1 output 'A'
(P9)
On/Off
Ch5
F2 output 'B'
(P10)
On/Off
Ch6
F3 output 'C'
(P11)
On/Off
Ch7
P1
Servo
Ch1
P2
Servo
Ch2
P3
Servo
Ch3
P4
Servo
Ch4
P5
Servo
Ch5
P6
Servo
Ch6
P7
Servo
Ch7
P8
Servo
Ch1
Selecta
Disabled
L input
Auto-detect
Monitors battery when used with a voltage booster
Arming
Enabled Ch1 to center position (off)
Low Voltage Cutoff
Enabled Led 5-flash if triggered (LVC)
Cruise control Disabled Motor cuts on signal loss/Tx switched off
Inactivity Sleep Enabled Invoked after 1hour, Switch Rx off and on to restart
Battery Voltage flashes
Disabled

2. EXAMPLE CONNECTIONS:


Motor (H1)

Led (F1 'A')

Led (P2)

Servo (P7)

Lipo booster (L)

'P' outputs are either 3.3v or 0v (ground). Leds need resistors to limit current to no more than 20mA. High brightness leds allow a lower current which is preferred (eg: 2-5mA). Google will reveal how to select resistor values but 220-470ohms will be safe starting values.

'F' outputs are buffered with a fet. They are 0v (ground) when on and floating (disconnected) when off. Up to 2A is possible but lower currents are much better. Current-limiting resistors are required for leds. The load is normally connected to positive and the F output provides a path to ground to switch it on. F outputs are marked with letters on the receiver (A, B, and C). The are programmed as P outputs (P9, P10 and P11). eg: F1 = A = P9.

The 'L' pad monitors a battery when used with a voltage booster. It is usually used with a single cell lipo but more cells can be used. This allows the motor to be powered with a boosted voltage and benefit from the convenience of a smaller lipo. The receiver will cut power to the motor when the voltage falls to below the LVC threshold determined when switching the receiver on.



3. BINDING

Bind once:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode.
3. Rx led should flash slowly; wait for it to go solid.
Change distance between Tx/Rx if binding does not work.




4. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; no signal or not bound if never stops).
5 flash = LVC/Brownout (voltage went too low; check battery/motor load).

5. PAPERCLIP CHANGES:
The following changes can be made by simply shorting two pads together (eg: with a paperclip):
1. Perform a 'Hard reset' (factory reset).
2. Change motor control between 'low off' and 'center off'.
3. Enable/disable LVC (eg: when using Nicads, NiHMs, LiFe cells).
4. Enable/disable Selecta.
5. Enable/disable Cruise Control/Failsafe.
6. Enable/disable the Menu feature.
'Paperclip' changes

6. PROGRAMMING:
This receiver has many other options that are described on the features page.
These are changed using a technique called 'programming': v611.


Home Videos About Buy Email