|
|
Rx65-5 Instructions (v611)
|
|
|
1. DEFAULT SETUP
|
Item |
Setting | Details |
|
Purpose: |
Rx65-5 |
'Car' setup for use with DX3 transmitter |
|
Red wire positive (+) Black wire negative (-) |
Battery |
3-18v Observe polarities |
|
H1 output |
Motor Ch1 |
Integrated forward/reverse ESC for brushed motors Center off |
|
F1 output 'A' (P13) |
On/Off Ch3 Driving lights |
Start disconnected, toggle when channel is Low Latching action, LED2 enabled |
|
F2 output 'B' (P14) |
On/Off Ch1 Reverse light |
Disconnected when off, 0v when on Auto activate |
|
F3 output 'C' (P15) |
On/Off Ch1 Brake light |
Disconnected when off, 0v when on Auto activate |
| P1 | Servo | Ch1 |
| P2 | Servo | Ch2 Steering |
| P3 | Left indicator |
Ch3 left <1s on, Ch2 steering/auto cancel |
| P4 | Right indicator |
Ch3 right <1s on, Ch2 steering/auto cancel |
| (P3/P4) | Hazards (Left+Right) | Ch3 left >2s toggle on/off |
| P5 | Flasher (0.5s) | Ch3 right >2s toggle on/off |
| P6 | Servo | Ch3 |
| P7 | Led | Ch3 toggle when low, latching action |
| P8 | Led | Ch3 toggle when high, latching action |
| P9 | Servo | Ch2 |
| P10 | Led | Ch3 on when low, momentary action |
| P11 | Led | Ch3 on when centered, momentary action |
| P12 | Led | Ch3 on when high, momentary action |
|
L input |
Auto-detect |
Monitors single cell lipo when used with a voltage booster |
|
Arming |
Enabled |
Ch1 to center position (off) |
|
Low Voltage Cutoff (LVC) |
Enabled |
Led 5-flash if triggered |
| Failsafe | Enabled |
Motor cuts on signal loss |
| Inactivity Sleep | Enabled |
Invoked after 1hour, Switch Rx off and on to restart |
2. EXAMPLE CONNECTIONS:
|
|
|
|
|
'P' outputs are either 3.5v or 0v (ground). Leds need resistors to limit current to no more than 20mA. High brightness leds allow a lower current which is preferred (eg: 2-5mA). Google will reveal how to select resistor values but 220-470ohms will be safe starting values.
'F' outputs are buffered with a fet. They are 0v (ground) when on and floating (disconnected) when off. Up to 2A is possible but lower currents are much better. Current-limiting resistors are required for leds. The load is normally connected to positive and the F output provides a path to ground to switch it on. F outputs are marked with letters on the receiver (A, B, and C). The are programmed as P outputs (P13, P14 and P15). eg: F1 = A = P13.
The 'L' pad monitors a single cell lipo when used with a voltage booster. This allows the motor to be powered with a boosted voltage and benefit from the convenience of a single lipo. The receiver will cut power to the motor when the voltage falls to 3v (LVC). The L pad is not intended for use when powering a receiver direct from a single lipo.
3. BINDING
Bind once:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode.
3. Rx led should flash slowly; wait for it to go solid.
Change distance between Tx/Rx if binding does not work.
4. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; no signal or not bound if never stops).
5 flash = LVC/Brownout (voltage went too low; check battery/motor load).
5. PAPERCLIP CHANGES:
The following changes can be made by simply shorting two pads together (eg: with a paperclip):
1. Perform a 'Hard reset' (factory reset).
2. Change motor control between 'low off' and 'center off'.
3. Enable/disable LVC (eg: when using Nicads, NiHMs, LiFe cells).
4. Enable/disable Selecta.
5. Enable/disable Cruise Control/Failsafe.
'Paperclip' changes
6. PROGRAMMING:
This receiver has many other options that are described on the features page.
These are changed using a technique called 'programming': v611.