|
|
Rx65-1-3A2 Instructions (v611)
|
|
|
|
|
|
1. DEFAULT SETUP
|
Item |
Setting | Details |
|
Purpose: |
Rx65-1 |
Train with joystick transmitter or any DT transmitter |
|
Red wire positive (+) Black wire negative (-) |
Battery |
3-18v (if no BEC) Observe polarities |
|
H1 output Direction |
Motor 1 Ch1 Ch3 |
Integrated forward/reverse ESC for brushed motors Low off (for full stick speed control) Move stick in required direction then center again Only effective when stopped |
|
H2 output |
Motor 2 Ch2 |
Integrated forward/reverse ESC for brushed motors Center off |
|
F1 output 'A' (P13) |
Front Light H1 (auto) |
0v when on, disconnected when off; LED2 enabled |
|
F2 output 'B' (P14) |
Rear Light H1 (auto) |
0v when on, disconnected when off |
|
F3 output 'C' (P15) |
On/Off Ch5 |
Start disconnected, 0v (on) when channel is Low Momentary action |
|
F4 output 'D' (P5) |
On/Off Ch5 |
Start disconnected, toggle when channel is Low Latching action, P5 controls 'D' |
|
P1 |
Front Light |
Auto action, 3.5v when on, 0v off |
|
P2 |
Rear Light |
Auto action, 3.5v when on, 0v off |
|
P3 |
On/Off |
Ch2, Idle high, 0v when channel is Low, Momentary action |
|
P4 |
On/Off |
Ch4, Idle high, 0v when channel is Low, Momentary action |
|
P5 |
On/Off |
Ch5, Start high, toggle when channel is Low, Latching action |
|
P6 |
On/Off |
Ch3, Idle low, 3.5v when channel is Low, Momentary action |
|
P7 |
On/Off |
Ch3, Idle low, 3.5v when channel is High, Momentary action |
|
L input |
Auto-detect |
Monitors single cell lipo when used with a voltage booster |
|
Arming |
Enabled |
Ch1 to low position (off) |
|
Low Voltage Cutoff |
Enabled |
Led 5-flash if triggered (LVC) |
| Cruise control | Enabled |
Outputs 'hold' last position on signal loss/Tx switched off |
| Inactivity Sleep | Enabled |
Invoked after 1hour, Switch Rx off and on to restart |
2. EXAMPLE CONNECTIONS:
|
|
|
|
|
|
'H' outputs are intended for brushed motors. H1 and H2 have different settings and are intended to be used independantly. H1 is on the main receiver board which has the green led. H2 is on the simpler daughter board marked 'A3'. H1 and H2 both have 3A ratings. This is a maximum 'worst case' value usually measured by connecting a fully charged battery direct to a stalled motor.
'P' outputs are either 3.5v or 0v (ground). Leds need resistors to limit current to no more than 20mA. High brightness leds allow a lower current which is preferred (eg: 2-5mA). Google will reveal how to select resistor values but 220-470ohms will be safe starting values.
'F' outputs are buffered with a fet. They are 0v (ground) when on and floating (disconnected) when off. Up to 2A is possible but lower currents are much better. Current-limiting resistors are required for leds. The load is normally connected to positive and the F output provides a path to ground to switch it on. F outputs are marked with letters on the receiver (A, B, C and D). The are programmed as P outputs (P13, P14, P15 and P5). eg: F1 = A = P13.
The 'L' pad monitors a single cell lipo when used with a voltage booster. This allows the motor to be powered with a boosted voltage and benefit from the convenience of a single lipo. The receiver will cut power to the motor when the voltage falls to 3v (LVC). The L pad is not intended for use when powering a receiver direct from a single lipo.
3. BINDING
Bind once:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode.
3. Rx led should flash slowly; wait for it to go solid.
Change distance between Tx/Rx if binding does not work.
4. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; no signal or not bound if never stops).
5 flash = LVC/Brownout (voltage went too low; check battery/motor load).
5. PAPERCLIP CHANGES:
The following changes can be made by simply shorting two pads together (eg: with a paperclip):
1. Perform a 'Hard reset' (factory reset).
2. Change motor control between 'low off' and 'center off'.
3. Enable/disable LVC (eg: when using Nicads, NiHMs, LiFe cells).
4. Enable/disable Selecta.
5. Enable/disable Cruise Control/Failsafe.
'Paperclip' changes
6. PROGRAMMING:
This receiver has many other options that are described on the features page.
These are changed using a technique called 'programming': v611.