|
|
DT Receiver - Rx43d-4-v502 - Programming
|
1. PROGRAMMING APPROACH:
|
|
|
1. Switch Transmitter on.
2. Hold left/right sticks (Ch2/4) in towards middle of Tx.
3. Switch Receiver on and wait for the Led to flicker very fast.
4. Center all sticks.
5. The led flashes the setting for the first 'Level' (eg: 1-flash = H outputs).
6. Yes = push the Ch3 (Elevator) stick forward (to top of Tx) to accept this and advance to next Level.
7. No = pull the Ch3 (Elevator) stick back (to bottom of Tx) to see next option for same Level.
8. Continue through all Levels until Led comes on solid.
9. Settings are saved automatically at the end so switch off at any time to abort.
10. Say 'yes' to every item to just see what is currently set.
|
Changing 'P2' from Ch4 to Ch5. Level 1: 3-flash = P Level 2: 2-flash = P2 Level 3: 1-flash = Servo Level 4: 5-flash = Ch5 |
2. PROGRAMMING OPTIONS:
|
Level 1 'H', 'F', 'P' or 'Other' |
Level 2 Output number |
Level 3 Output type |
Level 4 Channel number |
Level 5 Other choices |
Default | Information |
| 1 flash = 'H' outputs | 1-4 flash = H1-4 |
1 flash = 'Half stick' control (center off) |
1-7 flash = Channel 1-7 |
1112 1212 1313 1414 |
1/2 stick forward, 1/2 stick back, middle off Set 'Arming' position to 'middle' |
|
|
|
||||||
| 1 flash = 'H' outputs | 1 flash = H1 | 2 flash = 2 channel mix | 1-7 flash = 1st Ch 1-7 |
1 flash = 0% mix 2 flash = 12.5% mix 3 flash = 25% mix 4 flash = 50% mix 5 flash = 100% mix |
H1/H2 used as a pair (middle off) Set 'Arming' position to 'middle' |
|
| 1 flash = 'H' outputs | 2 flash = H2 | 2 flash = 2 channel mix | 1-7 flash = 2nd Ch 1-7 |
1 flash = 2 flash = |
H1/H2 used as a pair ('Reverse' option not implemented) |
|
|
|
||||||
| 1 flash = 'H' outputs | 1-4 flash = H1-4 |
3 flash = 'Full stick' control (can only use with 1 output) |
1-7 flash = Primary Ch 1-7 | 1-7 flash = Direction Ch 1-7 |
Low stick 0%, full stick 100% 'Direction' channel toggles forward/reverse (when 'Primary' channel is 0%) Set 'Arming' position to 'low' |
|
|
|
||||||
| 2 flash = 'F' outputs | 1-2 flash = F1-2 | 1 flash = Normal (low off) | 1-7 flash = Channel 1-7 |
2116 2217 |
Low stick 0%, full stick 100% | |
|
|
||||||
| 2 flash = 'F' outputs | 1 flash = F1 |
2 flash = 2 channel mix |
1-7 flash = 1st Ch 1-7 |
1 flash = 0% mix 2 flash = 12.5% mix 3 flash = 25% mix 4 flash = 50% mix 5 flash = 100% mix |
F1/F2 used as a pair (eg: Ch1 throttle) |
|
| 2 flash = 'F' outputs | 2 flash = F2 |
2 flash = 2 channel mix |
1-7 flash = 2nd Ch 1-7 | (eg: Ch2 steering) | ||
|
|
||||||
| 2 flash = 'F' outputs |
1 flash = F1 2 flash = F2 |
3 flash = Muscle wire / 2-coil actuator / 2 switches / ADD1 |
1-7 flash = Channel 1-7 |
F1/F2 used as a pair for steering; or Left stick gives Switch action on F1 (eg: light) Right stick gives Switch action on F2 (eg: light) |
||
|
|
||||||
| 3 flash = 'P' outputs | 1-2 flash = P1-2 | 1 flash = Servo | 1-7 flash = Channel 1-7 | 3112 | 1-2 servos no mix | |
|
|
||||||
| 3 flash = 'P' outputs | 1 flash = P1 |
2 flash = Servo 2 channel mix |
1-7 flash = 1st Ch 1-7 |
1 flash = 0% mix 2 flash = 12.5% mix 3 flash = 25% mix 4 flash = 50% mix 5 flash = 100% mix | P1/P2 used as a pair | |
| 3 flash = 'P' outputs | 2 flash = P2 |
2 flash = Servo 2 channel mix |
1-7 flash = 2nd Ch 1-7 |
1 flash = not reversed 2 flash = reversed |
P1/P2 used as a pair | |
|
|
||||||
| 3 flash = 'P' outputs | 1-2 flash = P1-2 | 3 flash = Brake or Reverse led |
1-7 flash = Activating Ch |
1 flash = Brake 2 flash = Reverse |
1 channel controls 2 outputs | |
|
|
||||||
| 3 flash = 'P' outputs | 1-2 flash = P1-2 |
4 flash = Left indicator led 5 flash = Right indicator led 6 flash = Flashing led (0.5s) |
1-7 flash = Activating Ch | 1-7 flash = Steering Ch 1-7 |
1 'activating' channel controls 2 outputs 1 'steering' channel cancels left/right Steer channel picks up 'trim' on startup Activ. stick left/right <1s = L/R on/off Activ. stick left >2s = Hazards on/off Activ. stick right >2s = Flasher on/off |
|
|
|
||||||
| 3 flash = 'P' outputs | 1-2 flash = P1-2 | 7 flash = On/Off led | 1-7 flash = Channel 1-7 |
1 flash = 'high' stick >2s on/off 2 flash = 'high' stick <1s on/off 3 flash = 'low' stick >2s on/off 4 flash = 'low' stick <1s on/off |
32711 |
1 channel controls 1-2 outputs Outputs 'toggle' on/off |
|
|
||||||
| 3 flash = 'P' outputs | 1-2 flash = P1-2 | 8 flash = On/Off led | 1-7 flash = Channel 1-7 |
1 flash = 'low' stick on 2 flash = 'high' stick on |
1 channel controls 1-2 outputs 'Center' = off |
|
|
|
||||||
| 4 flash = Other settings | 1 flash = 'Other 1' |
1 flash = Arming: Disabled 2 flash = Arming: Low stick 3 flash = Arming: Middle stick |
1-7 flash = Arming Ch 1-7 |
1 flash = LVC Disabled 2 flash = LVC Enabled |
41332 | |
|
|
||||||
| 4 flash = Other settings | 2 flash = 'Other 2' |
1 flash = LED2 Disabled 2 flash = LED2 Enabled |
1-2 flash = LED2 Pad P1-2 |
1 flash = No reset 2 flash = FACTORY RESET |
42221 |
LED2: use a Pad number that is driving any Led LED2: 'disable' if all outputs are servos Factory Reset = Restore Defaults |
|
|
3. DX3:
1. Use full 'brake' to make receiver enter programming mode on startup.
2. Use 3-position Aux channel to make yes/no choices.