|
|
Rx35d Instructions - v3.4.4
|
|
|
|
|
|
|
1. GENERAL:
3-10v may be connected with correct orientation to +/- points (4.2v if using on-board ESC).
The Rx is not insulated so take care to avoid short circuits.
The PCB is thin so do not bend it or exert great force on it.
2. LED:
Led On = perfect reception (real-time indicator).
1 flash = Scanning (~2sec between flashes; wrong model if never stops).
2 flash = Brownout (receiver voltage went too low; check battery/servo load).
3. FAILSAFE:
Outputs are not driven (do nothing) on startup and while scanning.
Outputs 'hold' on short signal losses (<1sec) and then do nothing (>1s).
4. BINDING:
1. Switch Rx on and wait ~20s until led flickers fast.
2. Switch Tx on in bind mode and Rx led should flash slowly and then go solid.
3. Change distance between Tx/Rx if binding does not work.
5.1 'SERVO' OUTPUTS:
Pads 1-4 will normally be used for servos or an external ESC (default)
Pad B will normally be used for Ch6 (Aux) (default)
Pad B can be changed to Ch5 (Gear)
Pad B can be changed to drive a second external ESC for 'dual-brushless' (see 5.4).
Pad A will normally be used for ESC2 (default)
Pad A can be changed to Ch5 (Gear)
Pad C will normally be used for ESC1 (default)
Pad C can be changed to Ch7 (Aux2)
Pad 3 can be changed to SumPPM or Serial for quadcopter type models.
5.2 BRUSHED ESC's:
Set Ch1/Throttle throws to 100%.
Close throttle to arm the ESC's.
Differential thrust steering mix can be enabled by:
1. set Level 1 'mix' to 12.5-100% (0%=disabled).
2. set Level 6 to Option 3 (4 servos + 2x ESC).
5.3 LOW VOLTAGE CUTOFF:
A 3.0v LVC is enabled by default but can be disabled.
The ESC will rearm if the throttle is closed briefly.
The led will have a 2-flash if LVC is triggered.
5.4 'DUAL BRUSHLESS':
Pads 1 and B can drive two external ESC's (eg: brushless) with steering mix. This feature is programmed with Levels 3 and 4 both set to 2 flashes.
6.1 PROGRAMMING:
|
|
|
1. Switch Transmitter on.
2. Make sure Ch3 (Elevator) is normal direction (not reversed).
3. Hold left/right sticks (Ch2/4) in towards middle of Tx.
4. Switch Receiver on and wait for the Led to flicker very fast.
5. Center all sticks.
6. The led flashes the setting for the first 'Level' (eg: 1-flash = 0% mix, 2-flash = 12.5% mix).
7. Yes = push the Ch3 (Elevator) stick forward (to top of Tx) to accept this and advance to next Level.
8. No = pull the Ch3 (Elevator) stick back (to bottom of Tx) to see next option for same Level.
9. Continue through all Levels until Led comes on solid.
10. Settings are saved automatically at the end so switch off at any time to abort.
11. Say 'yes' to every item to just see what is currently set.
|
Enable twin-steer: Level 1: 1-flash NO (down elevator), 2-flash NO (down elevator), 3-flash YES (up elevator) = Option 3 (25%) & move to next level Level 2-6: YES (up elevator) to all. |
6.2 PROGRAM LEVELS / NUMBER OF FLASHES:
Level 1: Steering Mix %
1 = 0% (Default)
2 = 12.5%
3 = 25%
4 = 50%
5 = 100%
Use 'Travel Adjust' in the Transmitter to fine-tune steering sensitivity.
Level 2: Steering channel (for mix)
1 = Ch4/Rudder
2 = Ch2/Aileron (Default)
Level 3: Pad 1 output ('brushless 1')
1 = Ch1(Throttle) (Default)
2 = Ch1(Throttle) + Steering mix
Level 4: Pad B output ('brushless 2')
1 = Ch6(Aux1) (Default)
2 = Ch1(Throttle) + Steering mix
3 = Ch5(Gear)
Level 5: Low Voltage Cutoff (brushed ESC's only)
1 = Disabled
2 = Enabled (Default)
Level 6: Output mix
1 = SumPPM on Pad2 (idle high) and Pad1 (idle low)
2 = Serial on Pad2 (idle high)
3 = Servo outputs on Pads 1-4, A=ESC, B=Ch6, C=ESC (Default)
4 = Servo outputs on Pads 1-4, A=Ch5, B=Ch6, C=ESC
5 = Servo outputs on Pads 1-4, A=Ch5, B=Ch6, C=Ch7